SEAL Image 6500 Spécifications télécharger pdf (Page 24)

WEBBING FILMS WITH A RELEASE LINER

The following are the basic webbing

procedures for webbing films with a release

liner:

• Select films slightly wider than the image to allow

for a border without film waste. A border of 1/8”

to 1/4” (3 - 6mm) is adequate.

• Load and center the films on top and bottom

unwind shafts with the dull adhesive side facing out

and the unwind brake tension released.

NOTE: Check if the film widths of the lower

and upper web are the same!

• TOP FILM: (film with a release liner) Pull the film

down from the top unwind shaft, behind the top

center idler and place it evenly over the face of the

top roller.

• Place a spare core over the front top wind-up idler.

Separate the film from the release liner. Attach the

release liner to the spare core using a piece of tape.

• BOTTOM FILM: Pull the film up from the bottom

unwind shaft, behind the front bottom idler and

place it evenly over the top film draped across the

face of the top roller. The two films will stick

together.

• Set the Shim Wheels to 1/16” (2mm) to allow for

the thickness of the leader-board.

• Use a leader-board to push the film(s) through the

nip.

• Lower the top roller and pivot the in-feed table into

position.

• Moving to the rear of the laminator ,use the foot

switch to advance the leader-board.

• Feed the leader-board over the first chill idler and

under the second chill idler.

NOTE: For top and bottom film combinations

of 10 mil or less, feed over the first idler and

under the second. For film combinations of 10

mil or over, feed over both chill idlers.

• Raise the top pull roller and advance the leader

board through the pull rollers.

• Holding the leader board up against the top edge of

the top pull roller lower the roller. Make sure the

rear Shim Wheels are set to ‘0’ (0mm).

• Return to the front of the laminator and set the

front Shim Wheels to –1/16 (-2mm).

• Using the footswitch advance the films, applying

light unwind brake tension gradually on both

unwind shafts until there are no wrinkles in the film

as it goes into the nip.

YOU ARE NOW READY TO FEED IMAGES!

Top

Main Roller

Top

Pull Roller

Front Top

Supply Shaft

Rear Top

Supply Shaft

Bottom

Main Roller

Bottom

Pull Roller

Chill

Idler

Shim Wheel

Print Guide

Front Table

Shim Wheel

Covered

Foot

Switch

Front

Chill

Idler

Rear

Front

Bottom

Wind-up

Rear

Bottom

Wind-up

Rear

Bottom

Supply

Shaft

Front

Bottom

Supply

Shaft

Rear

Roll

Easel

Front

Roll

Easel

Rear Top

Wind-up

Front Top

Wind-up

Top

Idler

Rear Table

Covered

Foot

Switch

Fan

Tube

Bott

Idler

Bott

Idler

Figure 19. Webbing for North America

Top

Main Roller

Top

Pull Roller

Front Top

Supply Shaft

Rear Top

Supply Shaft

Bottom

Main Roller

Bottom

Pull Roller

Chill

Idler

Shim Wheel

Print Guide

Front Table

Shim Wheel

Covered

Foot

Switch

Front

Chill

Idler

Rear

Front

Bottom

Wind-up

Rear

Bottom

Wind-up

Rear

Bottom

Supply

Shaft

Front

Bottom

Supply

Shaft

Rear

Roll

Easel

Front

Roll

Easel

Rear Top

Wind-up

Front Top

Wind-up

Top

Idler

Rear Table

Covered

Foot

Switch

Fan

Tube

Bott

Idler

Bott

Idler

Figure 20. Webbing for Europe & Asia

1 2 ... 19 20 21 22 23 24 25 26 27 28 29 ... 39 40

Commentaires sur ces manuels

Pas de commentaire

SEAL Image 6500 Spécifications Page 24

Commentaires sur ces manuels

Produits connexes et manuels pour Laminateurs SEAL Image 6500